What did you do to your 924/944/968 today?

andycowman · **Posted:** Sat Jul 06, 2013 9:59 am

Investigated broken central locking and passenger window, both fixed now and also moved the window switches to the centre console. Next up fitting remote central locking using a cheap eBay special!

Off to Canterbury for the night shortly so should give it another good long run

DaveM · **Posted:** Sat Jul 06, 2013 12:34 pm

Washed and polished the 968 so it's out to get it covered in bugs again this afternoon

Bow Runner · **Posted:** Thu Jul 11, 2013 7:08 pm

Tested my fuel guage a temperature gauges to eliminate them being faulty - both work - fuel sender must be the issue with the fiel gauge. Engine temp must be ok. Fixed the windscreen washers and the rear wiper. Tried to stop the rattle in the back hatch - failed due to seized hatch pins. Tried to change the wiper motor - failed due to the need to pull out the air box which would have been a major task and didn't have time. Fixed the glove box. Fixed the dash side trim.

Some tasks done. A few still to go. But progress at least.

Gj n pinky · **Posted:** Thu Jul 11, 2013 7:52 pm

Been to Lincoln and back on the new engine so it's nearly ready for its first oil change. This weekend will see it well over 500 miles.

Can't wait to have her run in properly I need to constantly remind myself to drive like a granny !

DaveM · **Posted:** Fri Jul 12, 2013 11:38 am

Good news that it's all back in one piece. Does that mean you'll be in it on Tuesday at the Whipping Stocks?

scam75 · **Posted:** Fri Jul 12, 2013 12:26 pm

Drove it and drove it some more. Rev limiter still seems to work!

Stuart

andycowman · **Posted:** Fri Jul 12, 2013 12:46 pm

scam75 wrote:

Drove it and drove it some more. Rev limiter still seems to work!

Stuart

Like this

Gj n pinky · **Posted:** Fri Jul 12, 2013 12:52 pm

DaveM wrote:

Good news that it's all back in one piece. Does that mean you'll be in it on Tuesday at the Whipping Stocks?

Should be all being well few little bits to sort out and it's now done over 500 miles so going to drop the oil this afternoon the hot weather is not agreeing with the running in piss that's in at the mo

lindsayhbrown · **Posted:** Sat Jul 13, 2013 9:01 am

scam75 wrote:

Drove it and drove it some more. Rev limiter still seems to work!

Stuart

That's always good to know, by the way what would you do if it didn't, I used to have a Pug 405 which didn't seem to have a limiter, saw 8k revs a few times :shock:

Matey · **Posted:** Sat Jul 13, 2013 10:39 am

Changed the drivers side electric window switch bezel, the one that was fitted looked like a combination of sticky tape and cable ties to sort of hold the switches in place :shock:

Rest of the day there's only one thing to do on a day like this, drive and enjoy ........

jordon0 · **Posted:** Sat Jul 13, 2013 12:02 pm

fitted new relays to abs pump to stop light coming on!
bulb removed for mot!!! not by me but place i got it from!
slowly getting through bits to get it good!!!!

scam75 · **Posted:** Sat Jul 13, 2013 9:55 pm

lindsayhbrown wrote:

scam75 wrote:

Drove it and drove it some more. Rev limiter still seems to work!

Stuart

That's always good to know, by the way what would you do if it didn't, I used to have a Pug 405 which didn't seem to have a limiter, saw 8k revs a few times :shock:

Guess I would do bad things to my engine lol! :shock:

Stuart

jonjeffryes · **Posted:** Sun Jul 14, 2013 10:35 pm

made Porsche Embossed door cards using the top from the embossed cards (with ruined bottoms) and the bottoms from my original door cards. A bit of careful cutting and joining together with copious amounts of glass fibre got the job done...on the hottest day of the year!

Althejazzman · **Posted:** Mon Jul 15, 2013 8:08 am

jonjeffryes wrote:

made Porsche Embossed door cards using the top from the embossed cards (with ruined bottoms) and the bottoms from my original door cards. A bit of careful cutting and joining together with copious amounts of glass fibre got the job done...on the hottest day of the year!

I see your plan worked!

jonjeffryes · **Posted:** Mon Jul 15, 2013 11:53 am

Althejazzman wrote:

jonjeffryes wrote:

made Porsche Embossed door cards using the top from the embossed cards (with ruined bottoms) and the bottoms from my original door cards. A bit of careful cutting and joining together with copious amounts of glass fibre got the job done...on the hottest day of the year!

I see your plan worked!

Yes, really pleased with the effect Alex. Looks better in the skin than in the photo's for once.

Porsche Enthusiasts Club Forum

What did you do to your 924/944/968 today?

Who is online