Page 2 of 18
Re: 944 89 Engine, gearbox transplant...
Posted: Wed Apr 08, 2020 9:54 pm
by 51rider
The groaning on mine stopped when I changed passenger

Re: 944 89 Engine, gearbox transplant...
Posted: Wed Apr 08, 2020 10:35 pm
by Crank Case
Hmmm... good idea. Is that filter generic to all 944's?
Re: 944 89 Engine, gearbox transplant...
Posted: Wed Apr 08, 2020 10:39 pm
by Crank Case
51rider wrote:The groaning on mine stopped when I changed passenger


Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 8:20 am
by Waylander
Crank Case wrote:Hmmm... good idea. Is that filter generic to all 944's?
Yes it is, and a load of BMW’s of about the same era
Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 9:57 am
by Crank Case
Thanks M.
I have ordered one.
Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 9:44 pm
by Crank Case
Wahey:
Can't seem to remove the power steering pump and i'm flummoxed as to how to remove the clutch from the bell housing.
Any suggestions welcome.
Ordered a PSP seal kit. Thought i'd do that before re-installation.
Here's the recon engine ready to go in. Shot was taken before I enamelled the rocker cover.

Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 10:43 pm
by 51rider
And posted at 9.44 to boot

Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 11:00 pm
by Crank Case
I hadn't noticed.
I'm totally pre-occupied with this 'thread 150mm M8 bolt to shaft, attach vice grips and tap with hammer' to get the clutch out of the bell housing malarkey.
What shaft?
Through(?) which hole?
Where?
'Thread' ?!
Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 11:17 pm
by Waylander
If you look closely at the rear mount bolt of the power pump you will see there is a collar in the hole
You have to jiggle that out and then the pump will come off, put a seal kit in the pump while it’s off, don’t drop the vanes!
Re: 944 89 Engine, gearbox transplant...
Posted: Thu Apr 09, 2020 11:32 pm
by Crank Case
Waylander wrote:If you look closely at the rear mount bolt of the power pump you will see there is a collar in the hole
You have to jiggle that out and then the pump will come off, put a seal kit in the pump while it’s off, don’t drop the vanes!
Oh i'll do it with it off. Watched a short vid on how to do it and it seems straight forward. I have to take it off the old engine and fit it to the recon one anyway.
Cheers, i'll look for the collar.
Still cannot figure out the clutch from the bell housing removal.
Re: 944 89 Engine, gearbox transplant...
Posted: Fri Apr 10, 2020 1:00 pm
by Waylander
You got manuals Rob,
All downloadable from
www.pdlibrary.co.uk
Re: 944 89 Engine, gearbox transplant...
Posted: Fri Apr 10, 2020 1:25 pm
by Crank Case
Yes, i've got access to that.
PSP pump was a doddle, thanks.
Clutch however...
Ended up using the angle grinder to cut the thrust bearing off (pics later) I am so glad that I haven't compromised the bell housing in any shape or form.
Now, if we use slightly different terminology in the sentence;
'thread 150mm M8 bolt to shaft, attach vice grips and tap with hammer'
'screw 150mm M8 bolt into the end of the clutch release lever axle/spindle and use the bolt to pull it out', it makes sense.
However, the above method requires levering against the bell housing or using a slide hammer and I was reluctant to do that. What I did was use a M8 flanged bolt and used a chisel against the flange of the bolt and tapped it out with a hammer. Bingo. Didn't stop me having to cut the diaphragm and thrust bearing though.
Clutch release lever roller bearings seem good. I don't know what the efficacy of replacing them is.
Received the engine mounts H - thank you.
Re: 944 89 Engine, gearbox transplant...
Posted: Fri Apr 10, 2020 9:03 pm
by Waylander
The bearing for the clutch release rod are a common size and can be bought anywhere, more important is the state of the shaft, has it got any indentations from the rollers, if so then a new one and bearings will be required
Re: 944 89 Engine, gearbox transplant...
Posted: Fri Apr 10, 2020 10:31 pm
by Crank Case
Waylander wrote:The bearing for the clutch release rod are a common size and can be bought anywhere, more important is the state of the shaft, has it got any indentations from the rollers, if so then a new one and bearings will be required
It looks good. I bought a complete clutch kit so i'll look at what I have and what I don't when it comes back from storage (with engine and box and starter ring and ignition leads and plugs and harness and ECU...).
I had to take off the fuel and filter assembly to get access to the drive shaft bolts. They were easier than expected. Left them soaked in de-blocker for 30 mins and then cleaned the heads out before hammering the alen socket in (12 times).
But the damn fuel filter mounting bracket rubber mounts came apart on me. Looked at Design 911 for the two replacements - £20.95 each plus VAT and carriage! The thieving sons of flea bitten motherless goats.
So I had a check at partworks.de. I really ought not to forget about those boys, (i've had orders from them before) and I got a pair for £13.95 incl. , free postage.
Everything that needs to be off the gearbox is off but can't get it off the torque tube...
That's Monday's job. I've burnt the candle out and i'm having the weekend 'off', re-charge the battery. Might do some fettling with the wire dizzy on the bell housing, front cross member and I intend to paint the torque tube heat shield. It's okay, no perforations but it's that 'whilst you're in there...'.
Oh here's a pic of that damn clutch:

Re: 944 89 Engine, gearbox transplant...
Posted: Fri Apr 10, 2020 10:36 pm
by Waylander
Sorry to be the bearer of bad news, the fuel filter mounts are standard bobbin mounts
They can be purchased from av mounts for £1.50 each
https://www.avindustrialproducts.co.uk/products
The release bearing pin will not be in the clutch kit nor the bearings