Porsche Enthusiasts Club Forum

It is currently Thu Mar 28, 2024 11:39 am
Classic Line Insurance


All times are UTC [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Wed Nov 14, 2018 3:36 pm 
Offline

Joined: Wed Nov 14, 2018 3:17 pm
Posts: 7
TIPEC membership: 8147
This is my first ever post so forgive my inexperience. I have an '87 3.2 Carrera Sport with 204K on the clock - the engine was rebuilt last at 170K. Sometimes it will run for 40 or 50 miles without issue, other days it will not go more than 100 yards without cutting out. It will stall on the drive when cold, it will cut out at any speed under load or not. Every time, I wait up to 30 seconds and it will restart on the key - often accompanied by a huge backfire. Here is what I have done so far to no avail...
- New ICV
- Replaced single wire CHT with new 2 wire
- Replaced air flow meter (reconditioned unit)
- Fixed vacuum leaks
- New auxiliary air Valve
- Refurbed injectors
- New coil
- New fuel pump
- New DME (Porsche OEM)
- New ignition leads, distributor cap and rotor arm
- Fuel injection set to factory settings by Bosch specialist
- Checked earths

Could the fuel pressure regulator be causing my problem (Over-fuelling)? Or an old imobiliser? Or the flywheel sensor? Or reference sensor?

I'm about ready to donate the car to the circus or roll it into a lake, so if anyone knows of a guru in the Bristol area or has some experience with a similar problem I'd welcome any feedback.

Thank you!


Top
 Profile  
Reply with quote  
 Post subject: Re: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Wed Nov 14, 2018 6:07 pm 
Offline
Moderator
Moderator
User avatar

Joined: Sun Nov 04, 2007 8:43 pm
Posts: 12645
Location: Chatham, Kent
TIPEC membership: 4190
OK you need to be methodical when it cuts you need to know whether fuel or sparks. I sounds to me like it could be a flywheel sensor, not necessarily bad but a bad connection or a fractured wire in the loom.

_________________
Jim

http://tipec.net/region_southeastlondon.php

2018 Mitsubishi Outlander PHEV
2005 Porsche Cayenne S Now sold!
2000 Jeep Grand Cherokee Now sold!
2010 Mazda MX5 Mk3.5 2.0 Sport Tech
2000 Porsche Boxster S SOLD!
1987 Porsche 944 2.5


Top
 Profile  
Reply with quote  
 Post subject: Re: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Wed Nov 14, 2018 6:21 pm 
Offline

Joined: Wed Nov 14, 2018 3:17 pm
Posts: 7
TIPEC membership: 8147
Thanks Jim, I have a new one ready to fit so that's an easy decision. The one in there looks quite new though so I have low expectations. Seems like spark to me due to the backfire, is there a way to know for sure when the problem happens? I only get a 20-30 second window before the car will restart and it always starts first time from cold.


Top
 Profile  
Reply with quote  
 Post subject: Re: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Wed Nov 14, 2018 7:57 pm 
Offline
Moderator
Moderator
User avatar

Joined: Sun Nov 04, 2007 8:43 pm
Posts: 12645
Location: Chatham, Kent
TIPEC membership: 4190
Could be the sensor we have had a few fail on 944s which use a Similar system, but the surrounding wiring looms have also been intermittent on some cars.
Quick question, does the recounted drop very quickly as it cuts out?

_________________
Jim

http://tipec.net/region_southeastlondon.php

2018 Mitsubishi Outlander PHEV
2005 Porsche Cayenne S Now sold!
2000 Jeep Grand Cherokee Now sold!
2010 Mazda MX5 Mk3.5 2.0 Sport Tech
2000 Porsche Boxster S SOLD!
1987 Porsche 944 2.5


Top
 Profile  
Reply with quote  
 Post subject: Re: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Wed Nov 14, 2018 8:46 pm 
Offline

Joined: Wed Nov 14, 2018 3:17 pm
Posts: 7
TIPEC membership: 8147
Not sure but I don’t think so. Most of the time it happens when I come off the throttle and everything seems normal until you go to accelerate again. All gaihes continue to work and the ignition lights come on as I dip the clutch.


Top
 Profile  
Reply with quote  
 Post subject: Re: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Fri Nov 16, 2018 5:32 pm 
Offline

Joined: Wed Nov 14, 2018 3:17 pm
Posts: 7
TIPEC membership: 8147
OK, I replaced the flywheel sensor and it started right up, ran for 45 seconds or so and died. Now it won't start at all. I check resistance at the ECU plug, flywheel and reference sensors read 998 ohms but when you crank the engine over I am seeing zero volts coming from both. CHT sensor measures 3,000 ohms when cold. Changed the DME relay (which was new), it started up for about the same amount of time and ran badly, then died. After 30 seconds or so of rough running, the CHT was reading 1,400 ohms.

I double checked the flywheel sensor gap and it's 0.8mm. Could the reference sensor be the cause of the problem?


Top
 Profile  
Reply with quote  
 Post subject: Re: Heeeeeellllp! My 3.2 engine keeps cutting out...
PostPosted: Fri Nov 16, 2018 5:43 pm 
Offline

Joined: Mon Nov 12, 2007 1:16 am
Posts: 4903
Location: Emsworth Hants
TIPEC membership: 993
Give Eddie at Silvertune a call, and explain your issues...he is in Christchurch and is an air cooled guru.

Call him on 07702465926 Tell him Steve Wagg suggested you call him, he will sort your problem.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group