| Porsche Enthusiasts Club Forum https://forums.tipec.net/ |
|
| LED Bulbs https://forums.tipec.net/viewtopic.php?f=27&t=11366 |
Page 3 of 3 |
| Author: | Bizman928 [ Tue Sep 06, 2011 10:18 pm ] |
| Post subject: | Re: LED Bulbs |
Mark I couldn't find mine either initially. It will be high up tucked away behind one of the boxes or tucked behind the actual fuse box itself. I can send you some more pics off-list if where I found mine if that will help. Steve |
|
| Author: | mark280 [ Tue Sep 06, 2011 11:07 pm ] |
| Post subject: | Re: LED Bulbs |
Steve , thank you any help would be fantastic!!! i really love this car and will get her just the way i want her Atb Mark |
|
| Author: | Bizman928 [ Wed Sep 07, 2011 12:10 am ] |
| Post subject: | Re: LED Bulbs |
No Problem Mark I will try to hunt them out These cars are infectious and put a very big smile on their drivers facevery timeime we take them out. Steve |
|
| Author: | Bizman928 [ Wed Sep 07, 2011 10:29 am ] | ||
| Post subject: | Re: LED Bulbs | ||
Hi Mark The connector plug should be tucked up above the Dim/Dip aluminium box on the left bulkhead in the footwell..see below. If it isn't there then look behind the fuse board or up above the fuseboard in the looms of wires & hoses. It may have been tucked there instead. Good Luck Steve
|
|||
| Author: | mark280 [ Wed Sep 07, 2011 8:45 pm ] |
| Post subject: | Re: LED Bulbs |
Steve, a BIG thank you!!!! ive just got in from work so will have a look after work tomorrow All the best Mark |
|
| Author: | mark280 [ Fri Sep 09, 2011 10:28 pm ] |
| Post subject: | Re: LED Bulbs |
Steve, I unscrewed the fuse board and with a torch found it, I'm so happy to have finally got the lights working properly. All in all amazing I've dropped the old girl off to be serviced, and cant wait to get her back. All the very best Mark |
|
| Author: | Bizman928 [ Fri Sep 09, 2011 11:38 pm ] |
| Post subject: | Re: LED Bulbs |
Hi Mark Thats great news. So glad you got it sorted. Hope she comes back sorted. Steve mark280 wrote: Steve, I unscrewed the fuse board and with a torch found it, I'm so happy to have finally got the lights working properly.
All in all amazing I've dropped the old girl off to be serviced, and cant wait to get her back. All the very best Mark |
|
| Author: | Porker928 [ Sun May 17, 2015 2:34 pm ] |
| Post subject: | Re: LED Bulbs |
I've now replaced the W3W lamps in the pod [instrument illumination] with LED's with good results.   I used 5mm ultra bright 3.3v blue LED's with a 660 ohm 0.6w in line resistor to limit the voltage. I heat shrunk the LED and resistor and mounted them on a small piece of double sided PCB to fit into the bulb holder and then bent the LED so that it points directly down when in final position. The tricky part is working out what the polarity of the socket is as they are all different depending on what model 928 you have! Mine was -+/+-/-+ [looking at the back of the assembly] Bench results here [not tested on the road yet ]   Ben |
|
| Author: | Bizman928 [ Sun May 17, 2015 5:16 pm ] |
| Post subject: | Re: LED Bulbs |
Ben You could have saved yourself a lot of trouble and drove round & picked up a fell set of dash bulbs in no time from us. Woodypeck Ltd sell replacement LED dash bulbs as well as all light bulbs for our 928's You are correct about the fitment & polarity of the socket. We found at our cost & the help or Paul Lacey who fitted some. Seems the early 928 are Grey caps and they have double contacts on both sides of the cap. The S2 has Brown caps & they have only the left contact each side active and the S4 has Black cap sockets and they are kike the early cars with double terminals on both sides of the caps. If you don't spot the difference you can short out the bulb - don't ask me how I know! Here are our 3w LED bulbs in the dash socket |
|
| Page 3 of 3 | All times are UTC [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|