Hi Adrian. A picture is worth a thousand words! Not sure what you mean
| Porsche Enthusiasts Club Forum https://forums.tipec.net/ |
|
| 968 boss to fit 944S2 https://forums.tipec.net/viewtopic.php?f=25&t=975 |
Page 1 of 2 |
| Author: | Adrian30 [ Thu Apr 10, 2008 12:15 pm ] |
| Post subject: | 968 boss to fit 944S2 |
Does anyone have any advice or know of a spare boss? i have the 968 wheel but the seller decided not to disclose it cam withou a boss. The wheel is 3 spoke and has three mounting holes. Have looked for boss tofit, but no luck. Can anone help? |
|
| Author: | J.J. [ Thu Apr 10, 2008 4:55 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Hi Adrian. A picture is worth a thousand words! Not sure what you mean
|
|
| Author: | Adrian30 [ Thu Apr 10, 2008 5:07 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Wish I could put a picture on for what I need but then that would mean I have the bit i need?Its the steering wheel boss to which the wheel screws (ie 3 screws only) and then the wheel and boss assembly is bolted to the steering shaft. |
|
| Author: | tr7v8 [ Thu Apr 10, 2008 5:13 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Is this a Porsche wheel or another aftermarket wheel? |
|
| Author: | Adrian30 [ Thu Apr 10, 2008 5:24 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Its a genuine Porsche 968 CS wheel, which i think is the problem as there are only 3 mounting holes so I think the most likely solution is a 968 boss;trouble is Porsche only supply the boss AND wheel together. |
|
| Author: | thegumeister [ Thu Apr 10, 2008 8:57 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Its the wiggly boss that sits behind the CS wheel, I am fitting a 75mm extension with longer bolts this W/End so I will take pictures for you |
|
| Author: | Adrian30 [ Fri Apr 11, 2008 7:50 am ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Thanks. That will give me a starting point. At least with it being wet I am not tempted to take mine out for a blast.....but there again, who can resist it! |
|
| Author: | thegumeister [ Fri Apr 11, 2008 4:17 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Here we go |
|
| Author: | lindsayhbrown [ Fri Apr 11, 2008 4:19 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
so you are the boss then 
|
|
| Author: | thegumeister [ Fri Apr 11, 2008 4:21 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
And again |
|
| Author: | thegumeister [ Fri Apr 11, 2008 4:23 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
And Again |
|
| Author: | thegumeister [ Fri Apr 11, 2008 4:42 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Last 1 |
|
| Author: | ExAudiSi [ Fri Apr 11, 2008 6:55 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
I didn't realise that came off seperately  Mind you, I wasn't looking for it to come off as I was replacing the air bag wheel with it! |
|
| Author: | Adrian30 [ Sat Apr 12, 2008 12:19 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Thanks ever so much for the pics, gives me something to work with. I don't suppose anyone has a spare boss like this? |
|
| Author: | Ben944S2Cab [ Sat Apr 12, 2008 6:42 pm ] |
| Post subject: | Re: 968 boss to fit 944S2 |
Looks like a standard momo boss with only 3 holes tapped in it. Either you could use a momo one and only use 3 screws if they are the same, or you may have to get them tapped up a couple of sizes. Take it to halfords and get them to show you any momo boss for any car w/o airbag and see if the holes line up. where abouts are you on the country? |
|
| Page 1 of 2 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|