Ok so here is a picture
tell me what bits you need for the washers
21 Retaining Valve £18
18 pressure valve £13
17 hose £8.63
10 washer jets £10 each
if they have prices they are normally available
| Porsche Enthusiasts Club Forum https://forums.tipec.net/ |
|
| Head Lamp Levelling System https://forums.tipec.net/viewtopic.php?f=25&t=24242 |
Page 1 of 1 |
| Author: | Picard1701 [ Sun Dec 08, 2019 8:53 pm ] |
| Post subject: | Head Lamp Levelling System |
I am trying to fix this system, the previous owner has cut all the wires out. The adjustment switch is still in the cabin and the step motors are behind the headlamps still. I need a wiring diagram for this system but it does not seem to appear in the online manuals. Does anybody have one? Thank you. |
|
| Author: | Waylander [ Sun Dec 08, 2019 9:29 pm ] |
| Post subject: | Re: Head Lamp Levelling System |
Check out www.pdlibrary.co.uk |
|
| Author: | Picard1701 [ Sun Dec 08, 2019 10:19 pm ] |
| Post subject: | Re: Head Lamp Levelling System |
Waylander wrote: Check out http://www.pdlibrary.co.uk What a great site. Thank you. |
|
| Author: | Waylander [ Sun Dec 08, 2019 11:01 pm ] |
| Post subject: | Re: Head Lamp Levelling System |
I keep looking for handy docs and how too's to add to it |
|
| Author: | Picard1701 [ Mon Dec 09, 2019 8:39 am ] |
| Post subject: | Re: Head Lamp Levelling System |
Waylander wrote: I keep looking for handy docs and how too's to add to it It's great. Especially the levelling motors article. I have spent all weekend undoing a major bodge in the headlamp washers, the lines had been cut and a nut screwed into the pipe with a jubilee clip. I suspect the pressure valves packed up and the system leaked. The levelling motors are a mess. They seem to have cut something out. I have a plug on passenger side (4 wires) cut. And in drivers side, plug cut (3 wires). I suspect the passenger plug merely taps to drivers plug (except I the have one unaccounted wire on passenger side) then drivers plug taps to loom. I found where I think the loom was cut out but it has only two wires (brown and green) was expecting 3 wires, the missing one one back to reostate in car. Hence a simple wire diagram with colours would be soooo great. I wonder whether if I do get this wired correctly, whether the lights will move, they look a bit rusty inside!! All great fun!! |
|
| Author: | Waylander [ Mon Dec 09, 2019 12:25 pm ] |
| Post subject: | Re: Head Lamp Levelling System |
Ok so here is a picture tell me what bits you need for the washers 21 Retaining Valve £18 18 pressure valve £13 17 hose £8.63 10 washer jets £10 each if they have prices they are normally available |
|
| Author: | Picard1701 [ Mon Dec 09, 2019 5:44 pm ] |
| Post subject: | Re: Head Lamp Levelling System |
Fabulous, I have ordered the pressure valve (missing), washer jets and a length of pipe. Thank you sooooo much. [p101tv][/p101tv] Waylander wrote: Ok so here is a picture
tell me what bits you need for the washers 21 Retaining Valve £18 18 pressure valve £13 17 hose £8.63 10 washer jets £10 each if they have prices they are normally available |
|
| Author: | Picard1701 [ Sun Dec 22, 2019 3:04 pm ] |
| Post subject: | Re: Head Lamp Levelling System |
Have fixed levelling motors and have the switch in the car. Still can't find the damn looms the previous owner cut the levelling motors from!!!! So annoying, I have practically removed the whole loom along the front of the car. Another owner send me pics of where the motors connect but the wires just are not there!! The whole engine bay is shocking in regard to looms repair, clips and routing of looms. One of the previous owners was a real git! |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|