Porsche Enthusiasts Club Forum
https://forums.tipec.net/

Which Wideband AFR Gauge / Sensor - 944 Turbo
https://forums.tipec.net/viewtopic.php?f=25&t=24057		 Page 1 of 1
Author:  Wh1t3Kn1ght [ Sat Aug 03, 2019 7:31 pm ]
Post subject:  Which Wideband AFR Gauge / Sensor - 944 Turbo
Hi Folks - looking for recommendations on an AFR gauge and wideband sensor, as you may have seen from my other thread I'm troubleshooting a rich fueling problem and would be great if I can see what is going on via the AFR gauge.

I'm pretty keen on the AEM digital gauges and also the Defi Racer gauges (not sure if Defi do an AFR gauge though).

Also for installation I'm guessing I just need to drill a hole which will allow the tip of the sensor to point down at an angle to avoid condensation and that a good location is in the exit pipe underneath the gear stick? If I drill the hole myself I guess I can then drive to a local garage and get them to weld the bung on for me?

Also another question - do any of you guys still have the stock O2 sensor? mine is jumpered currently using the correct plug, there is a sensor in the downpipe but I think it is toast - the good thing is that I can undo it (the reason it may not have been been replaced recently was that it was stuck). Should I replace it and remove the jumper plug and reconnect the O2 sensor?

Thanks!
Author:  scam75 [ Sun Aug 04, 2019 11:18 am ]
Post subject:  Re: Which Wideband AFR Gauge / Sensor - 944 Turbo
My car never had an O2 sensor. I have got and AEM ugo (spelling?) and it works well it has a digital read out plus an LED sweep which makes it really easy to see at a glance.

Stuart
Author:  pauly [ Sun Aug 04, 2019 3:18 pm ]
Post subject:  Re: Which Wideband AFR Gauge / Sensor - 944 Turbo
I've had an Innovate AFR kit on mine for 8 or 9 years. The standard narrow band sensor is still in the downpipe, but I doubt it's doing much after 28 years.
Author:  Wh1t3Kn1ght [ Sun Aug 04, 2019 8:31 pm ]
Post subject:  Re: Which Wideband AFR Gauge / Sensor - 944 Turbo
scam75 wrote:
My car never had an O2 sensor. I have got and AEM ugo (spelling?) and it works well it has a digital read out plus an LED sweep which makes it really easy to see at a glance.

Stuart


Hey Stuart - did you install your wideband sensor into the bung on the downpipe from the turbo? That is where my o2 sensor is so wondering if I just replace it with the wideband sensor and then I can output the narrowband signal to the stock o2 sensor wiring harness with the AEM gauge.
Author:  scam75 [ Sun Aug 04, 2019 9:39 pm ]
Post subject:  Re: Which Wideband AFR Gauge / Sensor - 944 Turbo
Yes I used the factory bung on the downpipe. You may be advised not to use this as it is too close to the turbo. However mine has been on for about 8 years and the sensor still works great and my readings have always seemed consistent enough. Maybe I have been lucky but either way it's worked just fine there. I do still have a spare bung and the plan was to locate it further down the exhaust if I had any issues or burnt out the sensor. Neither has happened. Standard Bosch sensor came with the kit.

Stuart
Page 1 of 1 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/