Porsche Enthusiasts Club Forum
https://forums.tipec.net/

Clutch Hydraulic Part Numbers
https://forums.tipec.net/viewtopic.php?f=25&t=23335		 Page 1 of 1
Author:  marks2ply [ Sun Apr 29, 2018 10:15 am ]
Post subject:  Clutch Hydraulic Part Numbers
Hi all

Could anyone help me with the part numbers for clutch hydraulics on my 944 s2. First item is the blue braided hose from clutch reservoir to master cylinder. The second pat required is the gasket between the master cylinder and body.

Any help with this would be great.

Regards

Mark
Author:  Waylander [ Sun Apr 29, 2018 3:27 pm ]
Post subject:  Re: Clutch Hydraulic Part Numbers
I will sort them out for you later, you can find the numbers in the download PDF

But it won’t tell you if they are NLA

think the gasket might be, and if you want cheaper I think you can get the blue hose from Just campers
Author:  IanK [ Mon Apr 30, 2018 8:45 am ]
Post subject:  Re: Clutch Hydraulic Part Numbers
If you dont mind it not being blue - I used this to replace my leaky hose....

https://www.merlinmotorsport.co.uk/p/7mm-cohline-brake-reservoir-feed-hose-per-100mm-m-sph8-4
Author:  edh [ Mon Apr 30, 2018 10:36 am ]
Post subject:  Re: Clutch Hydraulic Part Numbers
I need a blue hose as well - how is it connected to the reservoir? looks like a crimped connection?
Author:  Waylander [ Mon Apr 30, 2018 11:01 am ]
Post subject:  Re: Clutch Hydraulic Part Numbers
if you use the Petrol pipe type clips it will be fine there is no pressure involved

the hose is 999 181 021 50 220mm @ £24.67, Its 7.5 ID x 12.5 OD
The gasket is 928 423 191 00 @ £5.64

I would buy some sheets of gasket paper (.25, .5 or 1mm) out your local car parts store for about £2 and then you can make any of these little gaskets for next to nothing

If the two of you want to club up and buy this
https://www.coolairvw.co.uk/Item/Shop_b ... e-CB-.html

half each would get you a new hose for £7.00

This place sells interior lights for £7.50 Inc VAT, that's £5 cheaper than Porsche
Author:  edh [ Mon Apr 30, 2018 11:05 am ]
Post subject:  Re: Clutch Hydraulic Part Numbers
Thanks
I have new master & slave cylinders arriving this week, so might as well do the hose as well
Author:  Waylander [ Mon Apr 30, 2018 11:10 am ]
Post subject:  Re: Clutch Hydraulic Part Numbers
worth it as the hose can get a bit porous and draw air in,

Bleeding the clutch is always a massive pain, I did mine reverse, with a pumping oil can from underneath. what a pain in the ass
Author:  Endoman [ Mon Apr 30, 2018 11:00 pm ]
Post subject:  Re: Clutch Hydraulic Part Numbers
Changed my master and slave recently and fitted a remote bleeder. Makes the job a lot easier. I made my own gasker and used the pucka oertiker clamps (assorted set on ebay) The bleeder hose was made up specially by a local firm with a 7mm banjo on one end and a female on the other to take a std brake bleed nipple a small ali bracket mounted next to the clutch reservoir.
Photo is the one I did for the 993 which is equaly a pain to get at.

Attachments:
Slave.jpg
Slave.jpg [ 136.65 KiB | Viewed 6009 times ]
Page 1 of 1 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/