| Porsche Enthusiasts Club Forum https://forums.tipec.net/ |
|
| Is it so difficult? https://forums.tipec.net/viewtopic.php?f=25&t=1349 |
Page 1 of 1 |
| Author: | NEIL PARGITER [ Tue Jun 24, 2008 9:06 pm ] |
| Post subject: | Is it so difficult? |
QUESTION: How DO you change the side light bulb? Am I right in thinking its not as easy as it should be? Any suggestions? |
|
| Author: | JW590 [ Tue Jun 24, 2008 9:39 pm ] |
| Post subject: | Re: Is it so difficult? |
According to the haynes manual I have it says to look under the front of the car and you will see two plastic knurled knobs on the sidelight. Undo them and pull off the rear portion of the side light and change the bulb. I cannot check this as mine is an S2. Good luck with it. |
|
| Author: | J.J. [ Wed Jun 25, 2008 4:38 pm ] |
| Post subject: | Re: Is it so difficult? |
Do you mean the one in the head light or in the driving light in the bumper? The one in the bumper is easy. Just remove the black rubber over-rider. (One screw) then behind that are 3 screws. Take them out & the cover hinges back. Then you can get at the screws holding the spot light in! Havn't done the ones in the headlights yet! 
|
|
| Author: | jameso [ Thu Jun 26, 2008 6:41 pm ] |
| Post subject: | Re: Is it so difficult? |
J.J. wrote: Do you mean the one in the head light or in the driving light in the bumper? The one in the bumper is easy. Just remove the black rubber over-rider. (One screw) then behind that are 3 screws. Take them out & the cover hinges back. Then you can get at the screws holding the spot light in! Havn't done the ones in the headlights yet! Add to that drill out the rusted/sheered bolts and re-tap or replace with self tapping screws |
|
| Author: | J.J. [ Thu Jun 26, 2008 8:28 pm ] |
| Post subject: | Re: Is it so difficult? |
Mine came off easy!  The thing had been stripped recently for a respray!
|
|
| Author: | NEIL PARGITER [ Thu Jun 26, 2008 9:35 pm ] |
| Post subject: | Re: Is it so difficult? |
Thanks guys for all your comments. Got down to the car, undid the single screw to reveal....yep, I've got three rusted screws!!  Looks like I'll have to get the drill out and get busy!! Very concerned when I undo the three screws, will the trim pull back or does it just break off? Not liking the idea of that! Need some confidence boosting to the do the job!  Regards |
|
| Author: | jameso [ Thu Jun 26, 2008 10:24 pm ] |
| Post subject: | Re: Is it so difficult? |
The trim comes off very easily once you get the 3 screws undone/drilled out/snapped off, you would have to try really hard to damage it. If you do get them undone a bit of copperslip or grease on the bolts will make life easier next time |
|
| Author: | JW590 [ Fri Jun 27, 2008 8:26 am ] |
| Post subject: | Re: Is it so difficult? |
I think the Haynes manual I have is an American version, hence the different instructions because of the American safety bumpers. Another great buy off Ebay! I have to say I don't remember going under the car or having to put it on 'jackstands' - as the book says, when I had my 1989 944 2.7 Lux about eight years ago. By the way, that was a much more comfortable car than the S2. |
|
| Author: | tr7v8 [ Fri Jun 27, 2008 9:32 am ] |
| Post subject: | Re: Is it so difficult? |
john ward wrote: By the way, that was a much more comfortable car than the S2. What makes you say that? |
|
| Author: | lindsayhbrown [ Fri Jun 27, 2008 5:24 pm ] |
| Post subject: | Re: Is it so difficult? |
jameso wrote: The trim comes off very easily once you get the 3 screws undone/drilled out/snapped off, you would have to try really hard to damage it. If you do get them undone a bit of copperslip or grease on the bolts will make life easier next time when i changed to clear front indicators i managed to break the orange lense cover whilst undoing the rusty screws, so beware |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|