Porsche Enthusiasts Club Forum https://forums.tipec.net/ |
|
indicators not working https://forums.tipec.net/viewtopic.php?f=25&t=10722 |
Page 1 of 1 |
Author: | jabriel [ Tue Mar 29, 2011 7:37 pm ] |
Post subject: | indicators not working |
I'm in the middle of upgrading my interior lighting on my '91 944t but for some reason the indicators have stopped working!? Recently I finished replacing 3 bulbs in the instrument cluster with LED bulbs. (Using the popular silver foil technique.) Following that, I removed the rest of the dashboard trim and 3 further bulbs. (1 used for the cigarette lighter, 1 from behind the middle of the air vent, and I can't remember where the third one was. Would have to go back in the car and check in case its going to help.) Took the car out this evening and realised the left and right indicators aren't working. Other than the trim, I've reconnected the old bulbs and they are fine but the indicators don't work. Then main headlights and parking lights etc do work as they should. Any idea's what wrong or what I need to do? Thanks in advance. |
Author: | Lee 944 [ Tue Mar 29, 2011 8:07 pm ] |
Post subject: | Re: indicators not working |
Do the hazards still work? Not that this will help, I'm just curious? Because if they do, then it is the stalk. I had to replace mine on the 944, got one from Sulzeruk on here. |
Author: | lindsayhbrown [ Tue Mar 29, 2011 8:08 pm ] |
Post subject: | Re: indicators not working |
Do the hazard lights work ? |
Author: | Lee 944 [ Tue Mar 29, 2011 8:23 pm ] |
Post subject: | Re: indicators not working |
lindsayhbrown wrote: Do the hazard lights work ? I would say that great minds think alike, but someone will be along in a minute to say that fools seldom differ. ![]() |
Author: | lindsayhbrown [ Tue Mar 29, 2011 9:00 pm ] |
Post subject: | Re: indicators not working |
Lee 944 wrote: lindsayhbrown wrote: Do the hazard lights work ? I would say that great minds think alike, but someone will be along in a minute to say that fools seldom differ. ![]() ![]() |
Author: | jabriel [ Tue Mar 29, 2011 10:28 pm ] |
Post subject: | Re: indicators not working |
hazard lights not working either. Just realised - The only thing I haven't put back is the clock. (Not sure if that matters.) |
Author: | t3rra [ Wed Mar 30, 2011 5:55 am ] |
Post subject: | Re: indicators not working |
Not totally sure but I did read some wear that removing the clock and cig lighter can easily blow a fuse. But you prob check all them |
Author: | jabriel [ Wed Mar 30, 2011 7:39 am ] |
Post subject: | Re: indicators not working |
Sorry, my bad. Hazard lights are working. |
Author: | jabriel [ Wed Mar 30, 2011 7:57 am ] |
Post subject: | Re: indicators not working |
t3rra wrote: Not totally sure but I did read some wear that removing the clock and cig lighter can easily blow a fuse. But you prob check all them Came across this link - http://www.wiringdiagrams21.com/wp-cont ... se-box.png Not sure which fuse would need to be replaced for the bulbs. Anyone here know? Also, pardon my ignorance but how can one tell if a fuse is blown? (not ha to change one before so don't know.) |
Author: | David924S [ Wed Mar 30, 2011 9:59 am ] |
Post subject: | Re: indicators not working |
Checking a fuse is relatively easy you can see the join between the two contacts through the plastic case and if this is broken then the fuse has gone, or you can check with a volt meter set to resistance, it is sometimes more difficult knowing which fuse to check. |
Author: | jabriel [ Wed Mar 30, 2011 11:53 am ] |
Post subject: | Re: indicators not working |
That's easy enough. Anyone got any ideas about which fuse I need to check? |
Author: | t3rra [ Wed Mar 30, 2011 12:23 pm ] |
Post subject: | Re: indicators not working |
Under the fuse box lid, should be a diagram, the fuses are numbered, so u can check each fuse based on the indactours. Also there's a tester amount the relays, plug the fuse in and the light will glow if it's ok. Some time u can visually see a bad fuse. If the tester not there just replace the fuse 2 be sure. |
Author: | jabriel [ Fri Apr 01, 2011 11:43 pm ] |
Post subject: | Re: indicators not working |
Problem solved. it was a fuse. Thanks for your help everyone. |
Page 1 of 1 | All times are UTC |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |