Porsche Enthusiasts Club Forum :: View topic

Hello folks, posting on behalf of my brother (non-computer user) who has a sickly 3.2 2000 Boxter. Hope someone can help please. He's been told by his garage owning pall that a rebore will fix his problem and a local engineering firm they can bore 0.025 without problem (as they do with many engines - there were about 5 in being done at the time. They are unsure though if oversized big end bearings can be sourced from the standard 0.25 mm. He obviously doesn't want to proceed with the boring if there are no bearings out there to match the job. Can anybody please give some pointers of where there might be a supplier, or failing that, an alternative solution.

Many thanks

Author:	eboy [ Tue Oct 05, 2010 11:49 am ]
Post subject:	Oversized Big End Bearing?
Hello folks, posting on behalf of my brother (non-computer user) who has a sickly 3.2 2000 Boxter. Hope someone can help please. He's been told by his garage owning pall that a rebore will fix his problem and a local engineering firm they can bore 0.025 without problem (as they do with many engines - there were about 5 in being done at the time. They are unsure though if oversized big end bearings can be sourced from the standard 0.25 mm. He obviously doesn't want to proceed with the boring if there are no bearings out there to match the job. Can anybody please give some pointers of where there might be a supplier, or failing that, an alternative solution. Many thanks

Author:	ewan221 [ Wed Oct 06, 2010 10:08 pm ]
Post subject:	Re: Oversized Big End Bearing?
I would give Hartech a ring and ask their advice

Author:	911perv [ Tue Nov 09, 2010 8:42 am ]
Post subject:	Re: Oversized Big End Bearing?
Porsche only list standard size, its a new engine from them!

Author:	Brett928S2 [ Tue Nov 09, 2010 11:16 am ]
Post subject:	Re: Oversized Big End Bearing?
eboy wrote: Hello folks, posting on behalf of my brother (non-computer user) who has a sickly 3.2 2000 Boxter. Hope someone can help please. He's been told by his garage owning pall that a rebore will fix his problem and a local engineering firm they can bore 0.025 without problem (as they do with many engines - there were about 5 in being done at the time. They are unsure though if oversized big end bearings can be sourced from the standard 0.25 mm. He obviously doesn't want to proceed with the boring if there are no bearings out there to match the job. Can anybody please give some pointers of where there might be a supplier, or failing that, an alternative solution. Many thanks Hi Umm if they are reboring the CYLINDERS why would he need oversized bearings for the CRANKSHAFT ??? To be honest if there is so much damage to any engine that needed both rebored cylinders and reground crank, I would look for a second hand engine....much cheaper.... All the best Brett

Author:	bazhart [ Tue Feb 22, 2011 1:43 pm ]
Post subject:	Re: Oversized Big End Bearing?
If the bore is damaged we can supply and fit a new liner and piston. If the crankshaft is damaged there are no undersized shells from Porsche. Even if there were the crankshafts are only hardened as thick as a piece of thin paper and if the damage was ground out the surface would be soft and would not last long. We have had special shells made undersize and ground and re-hardened cranks that are presently under test in two engines - but we hve to test them for a few more months before we are certain they are Ok and can then offer them as an additional service. We have had slighlty oversized pistons made (also under test) for the 3.6 and 3.8 engines (and in manufacture for the 3.4 Cayman S) but have not needed to do so for the Boxster s or smaller versions as they seem to rarely need them - I guess one day we will. I hope this helps. Baz

Porsche Enthusiasts Club Forum https://forums.tipec.net/

Oversized Big End Bearing? https://forums.tipec.net/viewtopic.php?f=10&t=9650	Page 1 of 1

Page 1 of 1	All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/