Porsche Enthusiasts Club Forum
http://forums.tipec.net/

944 S2 Repair
http://forums.tipec.net/viewtopic.php?f=25&t=17102
Page 15 of 35

Author:  pauly [ Sun Mar 11, 2018 6:27 pm ]
Post subject:  Re: 944 S2 Repair

I'd wrap the discharge pipe, and the AOS. Not unheard of for it to melt with single skin downpipes.

Author:  sgl1966 [ Mon Sep 17, 2018 8:03 pm ]
Post subject:  Re: 944 S2 Repair

Unfortunatly been busy with work but hope to find more time soon . Vems looks like a very nice bit of kit with great support from Peep with all the little niggles you get . One issue I had which took a while to figure out was an arcing issue when trying to start the car causing the ecu to reset itself so unable to start . Like all good electrical problems this was intermittent . Found the cause to be that it was arcing from the cop to the cam cover . The rubber gasket is stopping a good earth with the cam cover . For the moment have just run a temporary earth which allows the car to start and run .
While trying to rectify this problem over a few weeks ,the rebuilt starter motor started complaining so have purchased a high torque motor from the states . Hopefully this will help turning over this larger capacity higher compression engine (9.5:1) .
And as for deja vu , here's a couple of pics of the next block with engine liners fitted . Gone for stepped liners this time . The pistons are some Arias 105mm 968 one's I have had machined down for an 8.5:1 cr as will be using a 2.7 head.

Attachments:
IMG_1090-640x480.JPG
IMG_1090-640x480.JPG [ 44.32 KiB | Viewed 11678 times ]
IMG_1091-640x480.JPG
IMG_1091-640x480.JPG [ 43.83 KiB | Viewed 11678 times ]
IMG_1092-640x480.JPG
IMG_1092-640x480.JPG [ 35.48 KiB | Viewed 11678 times ]
IMG_1093-640x480.JPG
IMG_1093-640x480.JPG [ 36.28 KiB | Viewed 11678 times ]
IMG_1094-640x480.JPG
IMG_1094-640x480.JPG [ 36.53 KiB | Viewed 11678 times ]

Author:  scam75 [ Tue Sep 18, 2018 12:49 pm ]
Post subject:  Re: 944 S2 Repair

Nice work Simon.

Author:  Gryphon [ Wed Sep 19, 2018 6:34 pm ]
Post subject:  Re: 944 S2 Repair

This is such an awesome thread hiding behind a really unassuming title. Excellent work here :)

Author:  sgl1966 [ Wed Sep 19, 2018 9:34 pm ]
Post subject:  Re: 944 S2 Repair

Thanks for the comments .
I fitted that starter motor today and a big difference . Not in the speed of turning the engine over which remains the same just the ease it does it continually . Lots of space to fit this even able to keep one of the heat shields.
I must say noise of the Holset turbo is quite impressive if not a bit scary . Should be a mighty engine .

Attachments:
IMG_1096-640x480.JPG
IMG_1096-640x480.JPG [ 33.23 KiB | Viewed 11578 times ]

Author:  pauly [ Thu Sep 20, 2018 11:49 am ]
Post subject:  Re: 944 S2 Repair

Hello Simon, looks like you're using 2 lambda sensors, is one for Vems and the other for a separate AFR gauge?

Author:  sgl1966 [ Fri Sep 21, 2018 5:04 pm ]
Post subject:  Re: 944 S2 Repair

Hi pauly , yes one for vems and one for the vems round gauge for AFR and EGT's .
You can see these on Vems Display but the round gauge was already fitted and a bit more discreet as well as allowing you to cross check numbers .

Author:  pauly [ Fri Sep 21, 2018 6:28 pm ]
Post subject:  Re: 944 S2 Repair

Hi Simon, reckon I'll keep my innovate AFR gauge too. Did you make the distributor blanking plate or buy that in?

Author:  sgl1966 [ Sun Nov 04, 2018 6:26 pm ]
Post subject:  Re: 944 S2 Repair

Pauly I had the plate water cut .

Had an oil pressure issue which I knew had to be fixed but the thought of what was involved is depressing when you have just got it all together .

After discovering the low oil pressure and unable to remove the geared drive from the oil pump I knew the front of the engine had to come apart . Bought one of these engine support beams from machine mart which holds the engine nicely from the engine mounts allowing the the suspension, steering rack and sump to be removed .

I did not remove the crossover just dropped the sump to allow the oil pump to be removed . This showed the reason for the low oil pressure . The teeth on the internal drive are all rounded and the gaps in between enlarged . This was a brand new oil pump internal part when installed and can only guess the teeth were not engaged properly when the bolt was cranked up( yes bolt done up to correct torque) allowing them to slip . I bought a new drive gear from Porsche which has changed in design for the better . The teeth are engaged or not with no room for a cock up.

Still all back together apart from the belts to do , just getting it ready to send of for paint in three weeks time .

Attachments:
IMG_1190-640x480.JPG
IMG_1190-640x480.JPG [ 43.53 KiB | Viewed 11343 times ]
IMG_1189-640x480.JPG
IMG_1189-640x480.JPG [ 54.66 KiB | Viewed 11343 times ]
IMG_1188-640x480.JPG
IMG_1188-640x480.JPG [ 48.52 KiB | Viewed 11343 times ]
IMG_1187-640x480.JPG
IMG_1187-640x480.JPG [ 27.9 KiB | Viewed 11343 times ]
IMG_1186-640x480.JPG
IMG_1186-640x480.JPG [ 37.49 KiB | Viewed 11343 times ]

Author:  pauly [ Mon Nov 05, 2018 12:34 am ]
Post subject:  Re: 944 S2 Repair

Hello Simon,

Have you thought about knocking up a 3 piece X member, like Lindsey sell?

Author:  sgl1966 [ Sun Nov 18, 2018 6:51 pm ]
Post subject:  Re: 944 S2 Repair

Yes Pauly , after the second time doing this . It looks like the pump was not the cause .

After bolting it all back together still no oil pressure . This surely meant it was either the pick up tube , possibly blown a hole in it when welding to strengthen it or poor seal with the Loctite on the crank cradle . So out it all came again, this time taking crossover out to drop sump.
All looked good when we took it of but swapped out pick up tube with another just in case and also replaced pick up tube seal . I must say the seal provided in the VH gasket sets seems to give a much better seal than the Porsche seal when compared together. Put the sump back on and turned it over on the starter and nothing ! Took out oprv , nothing ! Removed filter, back filled it and turned it over , not even an air bubble. Ran out of ideas by now thinking the engine has to come out but then had a look at another engine in the back of the garage and realised what the problem was .

I sent the block out to be cleaned before building which meant removing the core plugs to clean the oil galleys which they replaced on the front and back of block . Unfortunatly there is a third one inside the block in the oil galley prior to pump they had not replaced and I had failed to notice when building it which meant there was a 16mm hole sucking in air when trying to prime the engine . This plug is not even shown in the PET diagrams or shown on any of porsche systems . Still at a cost of £1.56 for a core plug and t2 days lying on my back on a concrete floor , all fixed .Turning itover on the starter is showing us 50+psi .
Wont forget to check that again in a hurry.

Attachments:
IMG_1210-640x480.JPG
IMG_1210-640x480.JPG [ 41.91 KiB | Viewed 11148 times ]

Author:  pauly [ Mon Nov 26, 2018 12:29 am ]
Post subject:  Re: 944 S2 Repair

I reckon you can over think things, I'd be twitchy about removing oil gallery bungs, and even core plugs. I've considered if I should rebore my 2.7 block, it's not scored and less than 0.002" out of round. It had good compression, so perhaps just a flash with the pads and paste would be enough.

Author:  sgl1966 [ Sun Dec 30, 2018 7:49 pm ]
Post subject:  Re: 944 S2 Repair

A happy new year to all .

While the road car is in for paint been spending some time tidying up the track car . Removed the battery tray to get to some surface rust which is a pain in the arse to get to and have had to do it to both cars . I find a flexible wand on the dremmel and a steady hand to cut the welds, soon has it out to get to the neglected area . Once cleaned and painted I find the 3m adhesives very good for putting the shelf back in.
Also having to find a way to attach the front lens covers again . Tigerseal has not held them in place but I think the paint is coming away from the border of the cover rather than the tigerseal not sticking to the lens. Going to cut down some small brackets and rivet them in place . Either that or the duck tape is coming out the box !

Attachments:
ResizerImage587X782.jpg
ResizerImage587X782.jpg [ 131.59 KiB | Viewed 10811 times ]
ResizerImage563X750.jpg
ResizerImage563X750.jpg [ 190.85 KiB | Viewed 10811 times ]
ResizerImage1011X758.jpg
ResizerImage1011X758.jpg [ 117.26 KiB | Viewed 10811 times ]
headlights.jpg
headlights.jpg [ 150.13 KiB | Viewed 10811 times ]

Author:  sgl1966 [ Mon Jan 28, 2019 9:26 pm ]
Post subject:  Re: 944 S2 Repair

Called in paint shop today and car is looking great .Should be back next week.

As always with most 944's , what should have been a little freshen up with the paint turned into a complete screen out bare metal respray. Although the sills were excellent unusally , had to replace both re arch sections behind wheels , glass boot pin holes and bottem of one wing . Fortunatly had enough repair sections from dead cars to make the task easier .

Attachments:
ResizerImage979X734.jpg
ResizerImage979X734.jpg [ 108.61 KiB | Viewed 10604 times ]
paint2.jpg
paint2.jpg [ 115.2 KiB | Viewed 10604 times ]
paint 3.jpg
paint 3.jpg [ 91.83 KiB | Viewed 10604 times ]

Author:  Waylander [ Mon Jan 28, 2019 10:12 pm ]
Post subject:  Re: 944 S2 Repair

Now that’s getting there, really nice

Page 15 of 35 All times are UTC [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/